After what seemed like a bizzillion practice cuts to double check the accuracy of the joints they are now completed. I've talked about this particular jig before and it's good but far from perfect and predictable. It's weakness is the method of adjusting which can be seen on the right side of the photo. There's simply too much variation possible when you have a metal screw head pushing against a thin wooden piece that is also attached to the fence. Sounds somewhat convoluted but if you're familiar with the Incra line of jigs and fences I can see the value of something along those lines. The down side the Incra line is their cost which can go up to five or six hundred dollars. The Dutch in me is trying to figure out how to make the adjustments on this jig more accurate. For starters, waxing the surfaces where the two fences slide together is worth pursuing. The other thing is to make the adjustment system entirely out of metal will be the next. If these pistol cases take off I'll definitely work on making the jig a "better mousetrap"!
You may notice the shiny spots on the two longer boards -- one of the thrills I get from resawing is that you never know what the grain will look like inside the board. In this case there were a few knot or worm holes which I filled with a sawdust/epoxy mix. Personally, I think that small knots or defects can add to the beauty of the piece, just so we don't get that knotty pine, cabin look on the pistol cases. The next phase of the cases is to size the panels and cut the dado for them. I'm going out Monday to talk to a perspective client that's needing some book cases built -- see what I can do for them!
Saturday, January 16, 2010
Tuesday, January 12, 2010
Curly Maple
If you've never seen curly maple before here's a quick shot of the panel for the doors. It's just all ripply and iridescent, Only finish on this will be shellac and wax.
Problem Solved!
In my last post I mentioned the slight dilemma about getting that continuos grain pattern with the limited amount curly maple I had. What you see on the assembly table is the inserts for the pistols -- they net out at about 3/4". The piece that is still in the clamps will be planed down to about 3/8" for the doors that go over the storage compartment. Anybody remember those types of clamps? I picked them up for $10.00 each at a garage sale and they really work to glue up a flat panel. The guy I bought them from was complaining about how difficult they were to use because glue sticks to them and wax paper wouldn't stay put. I solved that problem by screwing full lengths of that UHMW plastic to them -- nothing sticks to that stuff!
Saturday, January 9, 2010
Mission Picture Frame
Well, here is one of the corners of the completed frame. I took it to Larry at Artistic Framing, http://www.artisticframing.biz/ , so that he can mat the print, do his magic to keep the print looking good forever and place the matted print and glass into the frame. Glad to have it complete and now it's back to the pistol case project. Yesterday I went to Peterman Lumber to find a nice piece of maple for the panel the pistols will be displayed in. I lucked out and was able to find a nice piece of curly soft maple. Since the panel needs to be 9+ inches wide it was necessary to joint the edges and laminate them together. The trick is that besides the 3/4" thick panel needed for the pistol I also need a 3/8" piece to make the lid for the storage compartment. I believe in having the grain run continuously all the way through, from one end of the box to the other end. The lid is less than 7" long and my planer won't do a piece that short -- I do like hand planing but not a 7" piece of curly maple! Got that one figured out and I'll share that in my next blog.
Wednesday, January 6, 2010
Mission Style Picture Frame
I mentioned doing a small Mission style picture frame out of walnut and it's almost complete. I'd forgotten how small pieces such as this can be a challenge. The frame members are 7/8" thick with the sides being 1 1/4" while the top and bottom are 1" wide. I remembered (too late) that when cutting through mortises near the top of a piece you should leave the end long and trim after the joint is completely fitted. I think the proper name for that is a horn and it's purpose is to minimize the risk of splitting the thin end of the piece. Happily, if you too forget this it can usually be repaired with a little glue and clamp. The tenons are 3/8" thick and to chamfer the ends of them I used an old, Stanley plane that my stepson brought back from a trip to England. I sharpened it and it did a good job on the chamfers. I've received the small size kit from Lee Valley for making a wooden spokeshave which will give more control on these small chamfers.
At this point I've just completed gluing the frame together. It wasn't too warm in the shop and the glue was pretty thick so I warmed it up with a sink full of hot water! This was my first opportunity to use the torsion box as an assembly table and it worked well. The detail I wanted to show here is how you can make a U-shaped caul when you glue tenons that are proud of their mortises. I used very little glue, which once it was warm was easy enough to spread inside mortises. Rather have too little glue than have a mess oozing out. As far as strength there really isn't much required for a picture frame and tomorrow I'll be drilling for the ebony pegs that go completely through the joint.
At this point I've just completed gluing the frame together. It wasn't too warm in the shop and the glue was pretty thick so I warmed it up with a sink full of hot water! This was my first opportunity to use the torsion box as an assembly table and it worked well. The detail I wanted to show here is how you can make a U-shaped caul when you glue tenons that are proud of their mortises. I used very little glue, which once it was warm was easy enough to spread inside mortises. Rather have too little glue than have a mess oozing out. As far as strength there really isn't much required for a picture frame and tomorrow I'll be drilling for the ebony pegs that go completely through the joint.
Thursday, December 31, 2009
Happy New Year
Well here it is the last day of the year and we're on to a new one already! I feel as if I'm off to a blessed start because I have deposits for two more pistol cases. They will be the same general design as before but for different pistols and an added feature of having a spare cylinder in the case as well. I'll keep doing my blog to keep you informed. I've also been commissioned to make a Walnut picture frame in the Mission style. I selected a really nice piece of 5/4 Walnut from Peterman this morning. The frame will feature through tenons with an ebony peg in each corner.
But best of all, the torsion boxes are done and the shop seems larger already! This picture shows them set up and ready to be used as an out feed table for the saw. At this level it can also be used to place sheet goods on right out of the van or an assembly table. Anxious to use it and see if all the articles I've seen about them are true. I did give them a coat of amber shellac that was just about at its expiration date. The top surfaces have sacrificial pieces of 1/4" masonite screwed on.
When they are not being used I can store them like this. It really opens up the shop so maybe I won't feel like I'm tripping over things as I work. The two pieces of wood on top of the B&D Workmates are used to set the boxes even with the top of the table saw.
Monday, December 21, 2009
Building Torsion Boxes
For the last 20+ years or so I have had this huge assembly table I seem to always be running in to! It's been good but since size is limited in my shop I had to revise my lay-out. I used to be able to leave it down and park my truck on top of it but garages and vehicles have changed. It's supported by 2 of the old style, Black & Decker Workmates. Recently Fine Woodworking magazine had a feature about using 2 sawhorses and two narrow torsion boxes for your assembly table and even your work bench. Another thing is that Larry Yule from A.G. Yule and Sons Woodworking here in Las Vegas gave a demonstration at our Sin City Woodworkers meeting and showed how to make torsion boxes. These things prompted me to make some changes in my shop.
Here is a shot of the grid before the top and bottom pieces were attached. I covered the table saw to protect it from the glue but some went through anyway -- time to wax it again!
I decided to make the torsion boxes out of 1/2" Ultra-light MDF. The first step was cutting all of the pieces to make the grid. The overall size of the box will be 4" x 16" x 86". I tend to overbuild and over plan all of my work so I took the time to lay out all of the lines to help locate the nails. Even though I'm a die hard, hand tool kind of guy I sure was glad I had a nail gun to drive all of the brads. Each box has 4 long pieces (86") and then all of the cross pieces. I basically made two "ladders" for the outside grid sections and then toe nailed the center pieces to tie it all together. Once that was completed the top and bottom pieces were glued/nailed together. Usually I curse hot weather but with all of the glue I had to spread I was glad to have a 50 degree or so shop. I used Titebond III and a roller to slather all of the glue on. I chose it because it advertised the longest open time which I knew I'd need.
So, here's the completed box. I knew it was important that it be assembled on a flat surface and the table saw is the longest, flat surface I had. All that's left to do now is screw on a sacrificial piece of masonite (easy to clean off glue) and make pieces to rest it on so that it will also function as an outfield table for the saw. The other thing I'll do is trim the top even with the sides, left it slightly oversize so I could do this. I may get crazy and give it a coat of shellac too.
Subscribe to:
Posts (Atom)












