Monday, March 12, 2012

Prepping the Doors

     This type of work is not what I usually blog about but it's the project I'm getting ever deeper into.  Usually I share the hand cut joinery or smooth planed surfaces of some type of exotic or domestic wood species but this, it's different!  Diane and I have decided that since our original retirement plan of selling and downsizing our house has been scraped because of the economy we would just upgrade and repurpose the house we have.  Great neighborhood and neighbors so, why leave?  If you've been following along you know the first step was to get rid of the double tiered, fluorescent light box.  This was replaced with LED recessed lighting and the drywall will be re-installed and textured this Sunday.
     In the meantime, I've started removing the doors and prepping them for painting.  Something about those open cupboards that Ali just can't resist:

Just Checking Things Out!
 

     Sometimes you can hear her trying to work the door open which wasn't too hard with the old hinges.  Now there's no door but she's starting to lose interest, guess that like me she enjoyed the challenge.



   
     I won't get into the details of how I know this but I'm thankful for 3/16" dowels that are capable of plugging holes drilled in the wrong place!  I've decided to break the door prepping into manageable bites of 7 doors at a time.  I remove them, stamp a letter near the upper hinge position to know where they belong and then put a piece of masking tape on the corner that needs to be drilled for the handle.  Well, in the process it could hypothetically happen that you would drill the hole on the horizontal member instead of the vertical member of the door where it should be.  Remember the 3/16" dowel?  I decided there had to be a better way to mark them so my aging, sanding dust addled mind wouldn't make a mistake.  Just like so many other things in woodworking a simple jig was all that was required:

Marking Handle Position
     What this is is a two sided jig which should insure that the handles will be on the proper door member and at the same location.  Before removing the door I simply hook the jig over the top then use a scratch awl to center punch the location.  Easy now to drill a nice, straight hole on the drill press.  As of now, half of the 28 doors are ready to go and the rest will be completed tomorrow.  I'd really like to start the gesso process on the frame I carved in the workshop with Ian Agrell and I plan to fit that into my schedule.  Wouldn't you know that it's supposed to be windy most of this week and then there's a good chance of rain during the weekend.  That's going to make it difficult to spray the doors and drawers outside so I may have to start brushing the face frames and cabinet sides indoors.  I'll keep you posted.
   

Thursday, March 8, 2012

Second Session of Plane Making Class

     Last night was the second session of the class and unfortunately one of our members was absent.  Hopefully we'll get her caught up over the weekend, I'm sure we will.  At the end of the first session everyone had their main body parts cut, the recess for the chip breaker blade screw had been routed out, dowels were made, and things were ready to go together.  Jay, who is making a plane similar to my version of a scrub plane, had a bit more work so he came by over the weekend to my shop to finish a few details.  Now that the body is put together the next step is making and attaching the sole.
     Before that can be done, the bottom of the plane needed to be trued up and square to the sides.  This was done with a combination of planes and, as Lupe is doing here; using a piece of sandpaper on the flat and level surface of the table saw:

Checking the Plane Body for Square

     Jay is working on the same process, notice how his plane has a handle.  That's the part that is taking him a little more time since it needs to be formed, drilled, etc. to where it feels just right in his hands:

Jay using a Block Plane to true up the bottom

     Luckily, he has a shop at his house so he can work on his plane and not fall behind since his design is a bit more complicated.  To attach the sole to the body we use 3/16" dowels to register them together.  This is very important since the mouth opening (where the blade comes out) needs to be carefully made.  Theoretically speaking, the smaller your mouth the finer your cut.  I had them make their own 3/16" dowels for this purpose.

Making Dowels, Cutting out a Mouth, and Gettin' it Done!

     Last of all, work was started on making the wedge needed to hold the blade in place.  They all drilled out the location for the 1/2" dowel for that and we're good to go!  Next week we will first hone our blades and then see what kind of cut they are able to achieve.  Once that's done the final step will be forming the body to fit their hands.  That's accomplished with the bandsaw, spokeshaves, files, sandpaper, etc.
     Looking forward to seeing how well their planes will perform -- hopefully it will meet the expectations they had when they signed up for the class.

Tuesday, March 6, 2012

Kitchen Progress -- Slower than I Thought!

Well, here is that old cliche;
     
                          OUT WITH THE OLD -------




























AND IN WITH THE NEW:


Sorry, must be too tired to focus




This is what we finally decided to go with and now that 6 out of 8 are installed and burning brightly I'm really happy with them.  We bought these at Home Depot and they were one of the few items that received 5 starts from almost every reviewer.  We had tried the CFL bulbs but they were very blue and created a glare.  Almost decided to stick with incandescent flood lights and wait for LED's to drop in price but then saw these.  What's nice about them is that they are bulb and trim all in one.  At about $35.00 each this was a less expensive way to go then buying separate bulbs plus the trim ring.  We had tried an LED bulb and it too, seemed to leave quite a glare.  Most also show the separate LED's giving them a Jetson, space age look.  These don't have that and the bulb has a built in cover.  We should realize a great savings on these bulbs, rated at 65 watts but only use 14.5 watts.  I installed them in an air tight can and since they don't put out much heat (compared to other bulbs) we figure our a/c bill this summer will be a bit lower as well.
     Had a little bit of a problem with the Halo, 6" recessed cans.  I ended up asking my neighbor who works on kitchen remodels and installations to give me a hand.  He too had some hassles and mentioned that these had some grey foam on the clips, something he hadn't seen before.  Since we needed a total of 8 I bought an unopened case of 6 plus 2 loose ones.  The case had the clips without the insulation and installed much easier!
     Here's a picture of how these look now, I still need to add the final two by the window.  The way the kitchen is wired there are three switches, the four lights in the center are on one switch, the two over the bar are on another, and the last two by the window are on their own switch as well.


     Looking good!!  Replace the drywall, have an expert retexture the whole thing and then we'll paint it so this phase will be complete.

Monday, March 5, 2012

Kitchen Progress

A Gaping Hole
     After a couple of hours work and clean up time this is what we have now.  The hole is about 64" x 100" and took a while to open up.  After removing the existing fluorescent fixtures (3) the final piece of sheet rock was taken down.  The amount of bracing and blocking they put into this structure was crazy!  My cat's claw and crowbars worked overtime to get rid of it all.  Much of the backing was lower than the bottom of the rafters but I guess they didn't care about that since it was inside of the light box.  The floors are fairly clean with the steam mop but will need lots of TLC when the entire project is done.  That drywall dust even got between the seams of the laminate floor.
     I had a message from Ralph Bagnall  who encouraged me to check out LED bulbs.  We did and will probably go with them in spite of the additional added up front cost.  Bought a CFL lamp to test and it's really very bright and glaring.  That, combined with the warm up period is having us consider the LED's.
     Once the ceiling was removed and things cleaned up, Diane and I measured all of the features and made the floor plan.  It was drawn in 1/2 scale and here's the progression:

  The initial plan was drawn on to graph paper and then copied, upper left drawing.
Next the counters and upper cabinets were located, upper right drawing.
This was followed by locating the rafters and approximate location of the ductwork that we'll need to work around, bottom left drawing.
And the final plan is the colored version on the lower right.











     Now it's time to load up the truck with all of the destruction debris and haul it off to the transfer station in Henderson.  We plan to stop at the Bulb Man to get their advice on placement and number of fixtures we'll need to complete this phase of the project.

Sunday, March 4, 2012

Too Late to Change My Mind?

Ouch -- It's Beginning!
     Well, this isn't the normal post but I have the feeling this will be taking me away from the shop for a while even though my new carving chisels arrived yesterday.  Like many of you, our plans changed due to economy.  Seems like not too long ago the plan was to sell the big house and use the profits from the sale to downsize plus have a good chunk of change to use during retirement.  Since the economy retired about the same time I did in 2008 we are re-doing the house to keep it fresh.  No problem, we're just re-purposing and doing what we want to keep the house perfect for our use.  The project now is keeping the kitchen more current than it was in the 90's when we bought the house.

Oh So  90's
     Like many of the homes built in the mid nineties ours had this huge, dropped fluorescent light fixture and the Oak cabinets.  Part of the plan is to change the cabinets by painting them white.  There is one door I brushed white by the refrigerator that we put there to live with that change.  As much as I don't care for painted cabinets I agree with Di that this will really freshen up the over-all look.  The fixture just had to go!  When I got to the stage of the first picture I really did think that maybe it wasn't such a good idea after all.  Unreal the amount of nails and wood they used to build that monstrosity!  Much of it is solid lengths of 2x6 and the nails --------- bizillions of them!!  When I worked as a carpenter and built my own house, nail guns weren't very common.  If we lowered the ceiling we'd build soffits, almost like a ladder out of 2x4's and attach them to the rafters.  This darn thing had some of the crappiest wood and was nailed with a nail gun from every conceivable angle.  Pretty much impossible to simply pry the boards off so the cat claw I used in the 70's as a carpenter apprentice still came to good use!  It took me much of the day to get to this point:

End of the First Day
     I left the lights there for now and this will be gone by the end of work day #2.   Pretty amazing, the electrician who put these up didn't use a junction box and these lights are barely hanging on.  Guess they figure if it were to fall that awful Oak grid would catch it.  Definitely don't think this structure and electrical would have passed a  HGTV Holmes Inspection!

Thursday, March 1, 2012

Plane Making Class

     Had the first session of the class last night.  Got so wrapped up in helping them get started on making their own versions of the Krenov style plane I forgot to take pictures!  In the works are two different block planes using the 1" wide blade from Ron Hock, one general purpose plane with the 1 1/2" blade, and another plane that will be patterned after the scrub plane version I designed.  Found out that if you do a image search on any of the search engines my plane comes up under "Krenov Style Planes".  Must admit it's kind of cool to see my creation on the image page.
     Things were going well until one of the sides on a block plane split as the dowel pins were inserted.  Luckily it was at the dry fit stage and I had another piece of Australian Lacewood.  Looking forward to seeing how that turns out.  I think the students all enjoyed themselves in spite of some minor setbacks.  Two of them weren't too crazy about making their own dowels so opted to use a tenon cutter for that operation instead.  Making those dowels is time consuming but personally I like the results so feel the time is well spent.
     Next session we'll be gluing on the soles, learning how to hone the blades, and then setting up and using one of these planes.  The class is only 3 sessions so the last session will be spent on shaping the mouth and the plane body.  I'll be sure to take pictures next session.

Monday, February 27, 2012

Ian Agrell's Carving Class

Acanthus Leaf
     Well, I'm putting it out there for all to see.  To think that this started out as a 1" thick piece of African Mahogany that is about 7" wide and 13" long.  All hand work and to get to this stage was about two and a half days.  I put a couple of coats of shellac on it to seal and protect the piece.  The class was pretty intensive and with only 4 of us there we were able to get as much help as we asked for.  There's nothing like individual instruction from someone who's mastered this craft to point you in the right direction!  A dvd or pictures and text in a book just can't do that.
     I really felt like the table's were turned, many times my students would ask how in the world I'd do something and make it look so easy.  My reply was always "experience and learning from my mistakes", now I can feel their frustration in my own attempts to complete this leaf.  The class went from 9-5 every day and we'd take a lunch break but then keep on carving.  Very inspired and used the remainder of a gift certificate from Lee Valley to buy a couple of Hirsch carving tools as soon as I returned home.  Then I went to Woodcraft to order a few more Pfiel tools from them that I feel I needed.  Really like them and Ian highly recommended them as well.  Can't wait to get them and continue my learning curve.
     After finishing this required project I began work on two picture frames I'd brought from home.  They're made of Basswood so much easier carving but also easier to blow out the edges.  One of them is reeded and I plan to use it to work on my water gilding technique -- honestly not sure if there's enough time left for me to accomplish all I want to do in this life.  Some refer to that as a "bucket list" but since I keep adding things to it it's really not a list!  A plus to taking this workshop was being able to spend the week with my sister, something we hadn't done since we were kids and that was some time ago!